Tarvikkeet‪» Frame Protection‪»

Muc-Off Frame Protection Kit

Muc-Off Frame Protection Kit

Muc-Off Frame Protection Kit
Muc-Off Frame Protection Kit
Muc-Off Frame Protection Kit

Hinta
69,00 + toimituskulut
Sis. alv 24 %


Määrä
kpl



Väri
Muc-Off Frame Protection Kit Clear Gloss
Clear Gloss
Varastossa
Muc-Off Frame Protection Kit Clear matt
Clear matt
Ei saatavilla
Muc-Off Frame Protection Kit Day Of The Shred
Day Of The Shred
Varastossa
Muc-Off Frame Protection Kit Punk
Punk
Ei saatavilla



Valitse kaikki ominaisuudet.
Saatavuus
Osa tämän tuotteen malleista on vapaana varastossamme. Tämän tuotteen toimitusaika on heti, jos sitä on vapaana varastossamme ja muuten arviolta 3 - 15 vrk tilauksesta. Arvion luotettavuus on hyvä.

Varastotilanne ja saapuvat
Haluan ilmoituksen, kun tuotetta tulee lisää varastoon


Tuotteen kuvaus

Frame Protection Kit
EASY TO INSTALL / STRONG & DURABLE

Protect your frame’s paintwork and graphics against scratches, stone chips and cable rash thanks to our Frame Protection Kit - Clear. Featuring innovative TPU film technology that creates a smooth, stealthy, strong and durable finish
45-piece pack that will fit most DH, Enduro & Trail bikes or E-MTB bikes

 

HOW TO

  1. Clean your bike thoroughly before application. For best results and optimum durability spray Muc-Off Disc Brake Cleaner or Dry Degreaser onto a clean, dry microfibre cloth and wipe over the surface to ensure it is contaminant free. (Always test the disc brake/dry degreaser cleaner on a small inconspicuous area prior to use to ensure finish compatibility!)
  2. Try to fit the guards in a clean and warm environment, this will help achieve good adhesion to the surface. Top Tip! If you are applying in colder conditions and have access to a hairdryer then carefully warm the surface. This will help achieve an optimal adhesive bond. 
  3. Spray your hands and the adhesive side of the guards with water then slowly peel the guards off the backing material and line up the centre of the guards to the area you are applying. NB: It’s important you start with each sticker in the dead centre of the area you are applying so chill and take your time on this section! Then slowly rub down the middle, working your way out to the sides pushing out any air bubbles to the edges. 

Top Tip!

You can easily trim the shapes as required, if necessary, with clean, sharp scissors if you need to fit around any challenging shapes or frame mounts etc.

  • Use a clean microfibre cloth to firmly rub down the guards onto the surface and make sure you cover all areas with even pressure.
  • Sit back and admire your freshly wrapped pride and joy, now go ride!

REMOVAL: Ready to remove your guards? Removal is easy!

  1. Start by gently heating the surface of the guards with a hairdryer. This will help soften the adhesive, then slowly start peeling up a corner of the guards and peel back as carefully as you can, try to keep the adhesive attached to the protective layer so it all comes off in one piece. 
  2. Once each protection guard is removed use Muc-Off Glue & Sealant Remover to easily remove any residue before re-installing your new guards! (Always test the Glue & Sealant Remover on a small inconspicuous area prior to use to ensure finish compatibility!). *age restrictions may apply!

Please note - not suitable for frames with an anodized finish. Anodized finishes do not provide a suitable surface for the application of the clear protection because the adhesive struggles to conform to the coarse texture, trapping moisture and air underneath the film. This can result in tricky application and bubbles underneath the frame.


Kommentit
Lisää kommentti

Tuotemerkki